Simplified Measurement Verification Practice Test

These questions are part of the practice quiz. Start practicing

• Which statement best describes zero drift?
• The overload capacity concept is best described as which of the following?
• What should you do if verification results show bias across the range?
• Which hardness testing methods are specified for rigid metal measures?
• Anti-drain valves are found on which hose condition?
• Which expression accurately represents the watt?
• Top diameter of commercial dry measure exceed bottom by:
• Code 3.30 covers which liquid?
• Which meter disk has a magnetic bearing system?
• Maintenance tolerance shall not exceed plus or minus 2% on full or light load.
• The gasoline gallon equivalent is equal to 5.66 pounds.
• In verification terms, what is the difference between accuracy and precision?
• Milk tanks are used to determine quantity of milk. Which option reflects a correct assignment?
• Search warrant is executed within_____ days after it has been issued by a judge.
• Testing medium for vehicle tanks?
• What is field verification?
• Dry hose discharge line is required for use with.
• Where on a big-volume rigid measure is the capacity typically marked?
• In the variable frequency inspection plan, who determines the testing scope?
• Test drafts of at least four times the minimum registered volume are required for which type of device?
• The dry measurement regulations apply to:
• What is the minimum wholesale liquid test draft?
• What best describes repeatability?
• Which indicator presents values as numbers on a device that advances intermittently?
• What is the role of a master standard?
• On a retail blending device of its capacity type, means shall be displayed to:
• How should traceability be demonstrated across measurements and standards?
• Practical unit of electrical resistance is
• What metrics are commonly used to monitor verification performance over time?
• What is a tolerance or specification?
• Which statement correctly describes the dollar value computation elements?
• What is a working reference standard?
• The statement 'When performance falls within applicable tolerances for that device, the device is said to be accurate' is
• Maintenance tolerance shall not exceed what value on full or light load?
• For wholesale meters, the smallest unit is 5 L or 1 gallon.
• Maintenance tolerance for the odometer test on a truck loaded to its 1/2 capacity is?
• The energy unit defined as energy delivered in one hour at a rate of one watt is which?
• What defines a control plan for measurement verification?
• Which item is NOT typically found on a calibration certificate?
• Which document governs the installation standards for measuring devices?
• The variable frequency inspection plan shall provide testing of all commercial devices on:
• How do SOPs relate to measurement verification?
• What is the relationship between a master standard and working standards?
• Test Drafts of all water meters are defined as which of the following?
• What information is typically found on a calibration certificate?
• Which statement best defines a Gage R&R study?
• Which unit is used to represent energy consumption over time in electrical metering?
• A vehicle tank used as a measure is required to have an expansive percentage of
• The prefix kilo represents which numerical value?
• What does a Gage R&R study assess in practice?
• Define precision in this context.
• Which statement best describes a linearity check?
• Maintenance tolerances apply to measuring equipment after which events?
• Testing medium for fabric measuring device.
• What is the role of acceptance criteria in a verification plan?
• IQ/OQ/PQ and how they relate to measurement verification?
• Which material is used for the ends of a wooden yard stick?
• What are repeatability and reproducibility?
• Milk tanks are used to determine which of the following?
• Unless compartments or tanks have been damaged or modified or the chassis modified or unless the marker seals have been broken, a compartment or tank shall be tested:
• LPG with digital display has to have a minimum delivery of no less than divisions:
• Acceptance Tolerance relation to Maintenance Tolerance
• Reinforcing rings on rigid measures of liquid volume shall be attached to:
• Which statement about Code 3.30 is true?
• For 3-wire service loads with a 120-208 volt network, meters shall be what type?
• In gravimetric measurement of liquids, which statement is correct?
• Which metric is used to quantify the spread of verification results?
• Which statement describes verification action?
• What court hears misdemeanor cases/violations?
• Which statement correctly describes a requirement for ensuring accuracy in wire and cordage measuring devices?
• What is the maintenance tolerance on a lube meter for a 1 pint measurement?
• Vehicle tank gravity discharge hoses are part of which type?
• When measuring a liquid gravimetrically, which factors must be considered?
• What is the testing medium for non H2O measuring devices?
• Where should the value figures be placed on a glass graduation?
• Which of the following best describes a farad?
• Why verify across the full measurement range rather than at a single point?
• Which statement is true about the inspection frequency for linear measures?
• Rigid measures of liquid volume, made of metal, must meet standards of?
• What is the maximum permitted length for a retail discharge hose?
• Measure of the rate of flow of electrical current is
• What is measurement uncertainty?
• Batch Plant water meters smallest unit description?
• For the 35 gallon test draft, the maintenance tolerance value is shown as
• What does traceability mean?
• Flex tape measure is made of:
• How do you calculate a simple accept/reject decision from a verification check?
• On the front plate of a watt-hour meter, which item is not required?
• Measuring equipment shall be operated only in the measure:
• When should a verification interval be reassessed or changed?
• The statement 'When the device meets all requirements, tolerances and specifications it is said to be correct' is
• How does verification differ from calibration?
• What is the unit of active power in electrical circuits?
• What best describes reproducibility?
• Which statement describes the relationship of a verification check to instrument performance?
• Distance necessary for stabilizing tire temperature prior to the mileage test on an odometer:
• When equipped with a discharge valve, a rigid measure of liquid volume shall be susceptible of?
• How does temperature affect verification results for a sensor?
• The minimum discharge rate for a wholesale liquid measuring shall not exceed which percentage of marked discharge?
• Farm holding tanks are tested volume at what frequency?
• Corrected instrument by device repairman
• Graduations on a graduate should be oriented relative to the axis as:
• What is the overload capacity of a meter defined as?
• Which device type requires a test draft of at least four times the minimum volume?
• What action is typically taken when a measurement is out of tolerance during verification?
• Regulations covering subdivided glass measures of capacity, either cylindrical or conical in shape, applies to:
• How often should verification be performed for critical instruments?
• Which type of meter is exempt from maintenance tolerances?
• Non-destructive verification is preferred when:
• What does documentation in a verification plan typically include?
• What is the difference between an audit and a verification check?
• What is a basic sampling plan in the context of verification?
• Except for electrical meters, Maintenance tolerances shall apply to measuring equipment?
• Electrical pressure causing electron flow in a current is
• On glass graduates, the position of value figures is:
• How can training impact measurement verification results?
• What role does a reference standard play in traceability?
• What is span drift?
• Which of the following is NOT a stated testing medium for vehicle tanks?
• Capacity marking on 1/2 bushel of dry measure:
• Directional flow valve auto in operation on everything except which category?
• What is data integrity in verification?
• Which statement best describes a watt?
• Schedule of extras on a taxi should be placed:
• Acceptance Tolerance (AT) is defined as half of the maintenance tolerance.
• In field verification, which equipment is typically used?
• How does MSA support simplified verification?
• What constitutes a nonconformance in the verification process?
• Define accuracy in the context of measurement verification.
• Farm milk tank designed:
• A farad is the SI derived unit for which electrical quantity?
• Linear measures regulations apply to any measure of length, whether it is:
• Minimum total of milk tank equal to the volume corresponding to the gauge:
• Correction applied to gasoline is:
• The maintenance tolerance on a retail meter fuel device at a test draft of 35 gallons is which option?
• Placing commercial weighing and measuring devices into service are adopted by?
• Which statements describe the required handling of wire and cordage measuring devices?
• If a meter installation has more than 240 volts between phases, which item ensures safe test access?
• A linear measure shall: (alternate phrasing)
• What is the difference between single-measurement verification and repeated measures verification?
• The maintenance tolerance for a 1 pint measurement on a lube meter is expressed in which unit?
• Which meter is not covered by the liquid measuring device code?
• The primary indicating element on a commercial weighing device serves which purpose?
• What is a primary purpose of applying a security seal to a discharge valve on a rigid liquid measure?
• Which device is used to measure active power in an electrical circuit?
• Width of graduations on linear measure shall not exceed _________ the width of the smallest measure and shall in no case be wider than 0.03 inches.
• Which container size is not permitted?
• Which of the following is a testing medium for vehicle tanks?
• In measurement verification, a vehicle tank reading of 0.04 requires a change to which value?
• What is the purpose of a capability study in verification?
• For a retail blending device, which information must be displayed?
• Which statement best defines a watt?
• What is the frequency of inspection for fabric measuring devices?
• What unit is used to express the maintenance tolerance in the example?
• How do you perform a simple uncertainty budget for a verification?
• What is bias?
• Which unit does a meter clearly register to measure energy usage over time?
• Name an environmental factor that can affect verification results.
• For all 3-wire single-phase service loads on 120-208 volt networks, the meter shall be of which type?
• What is the purpose of using repeated measurements in verification?
• What is the purpose of a measurement verification plan?
• Which is NOT a legal basis for calculating fare with a taximeter?
• What is a non-destructive verification?
• How can environmental control be incorporated into verification?
• Which standard governs placing commercial weighing devices into service?
• What is an out-of-tolerance action plan?
• Which option describes within-lab reproducibility?
• Graduations on a graduate shall be:
• Why is calibration certificate traceability important?
• Linear measures regulations apply to any length measurement irrespective of whether the measure is:
• What is the primary purpose of measurement verification in a simplified process?
• Test Drafts of all water meters are:
• Blondel's theorem best describes the relationship between power in a system of conductors and watt-meters. Which option is correct?
• Why is documentation important in verification?
• Which is an example of a security seal?
• What is the required frequency of visual annual testing for farm holding tanks?
• How can environmental effects be mitigated in measurement verification?
• What does a basic sampling plan help determine in verification?
• How should verification address measurement range to ensure accuracy?
• Rigid measure of big volume shall be marked with its capacity on the:
• The front name plate or register of electric watt hour meter must have all except:
• Wood yard stick ends:
• Which statement about LPG testing is true?
• System of indication or of the selector type or one advances intermittently, in which all values are presented as numbers:
• The top edge dry measure is made of which material?
• Article 18 requires graduations to be made of
• LPG with digital display minimum divisions (latest format)?
• Which practice quantifies measurement system variation and ensures consistent results in verification?
• What is the unit of power defined as energy per unit time?
• What is the maximum length for a retail discharge hose?
• In verification, which statement about a standard used for regular checks (working reference standard) is true?
• Frequency of inspection for linear measure is:
• Which option is not typically included in a measurement verification control plan?
• What does system suitability mean in the context of measurement verification?
• How should traceability be demonstrated in verification?
• What does the interval in a verification plan specify?
• Which unit correctly represents energy delivered when one watt is expended for one hour?
• In the metric system, which prefix denotes one thousand?
• Which statement best describes a Gage R&R study in practice?
• A meter installation with nominal voltage of more than 240 volts between phases must be equipped with which item?
• Testing medium for fabric measuring device.
• Dollar value computation elements of a retail measuring device shall be:
• Measuring devices must be installed in accordance with?
• In Blondel's theorem, the total power in a network of N conductors is measured by how many watt-meters?
• A linear measure shall:
• Which statement best defines Gage R&R in evaluation?
• Batch plant H2O meter shall indicate its deliveries in gallon and subdivisions on a gallon. The max value of the smallest measurement unit of registration, if the delivery rate is less than 100 gallons, minute, shall not be greater than:
• What is within-lab reproducibility?